Possible Calibration Techniques:
As discussed on the homepage (water
color explanation), the color change and the particulate formation you
observed can only be used as crude indicators of the toxins being
detoxified from your body; this was explained by the fact that only a
small percentage of the water change is actually due to material being
pulled out from your body. Most color change is from the unit consuming
the metals in the array during the ion generating process, and from these
generated ions neutralizing dissolved particles, salt, and toxin in the
water, (in the same manner as it would have neutralizes toxins drawn out
of your body).
Because almost all of the color change could be due to the regional
toxicity in the water supply used for the bath and the leaching from the
array metal (depending on it's stainless steel composition), should you
run the system without your feet, you will still observe color changes,
only different then when your feet is in the water; even if it may not
appear to be different, it is. It's just that the more intense color
effect caused by the array and salt has masked the fainter color change
produced by materials leaving your body.
If you were able to calibrate and roughly subtract the color effect due to
the sea salt added and the leaching from the metals of the array, you
could actually use the unit to either measure your toxicity or observe the
toxicity of your regional water supply. A possible way to do this
approximate calibration comparison technique is to first establish the
reference color change that represents no chemicals contaminants in the
water (other than from the sea salt added and from the leaching of the
metals of the array ); this reference color can be established by running
the unit without your feet, using distilled water. If you run the unit
with distilled water, the color change you observe does not include the
effect from the regional water supply; however, it still includes the
change due to the sea salt you add as well as from the leaching of the
metals of the ion generating array. To evaluate your toxicity by making a
comparison, run the unit with your feet in distilled water. To evaluate
the toxicity of your regional water supply, run the unit without your feet
using the regional water supply, and compare this result to the reference
result using distilled water (both without feet).
To make an accurate comparison, it is required that you use the same
amount water, and add exactly the same amount of salt for each run; if you
use different amount of salt and water, you cannot make a credible
scientific comparison. You can only make a credible comparison if you are
sure that the color change caused by the sea salt added and the array are
the same for all runs. Make sure that the size/type of array and the
amount of sea salt added is the same for all runs!
Before sea salt is added, amperage reading and voltage is a property of
the water and/or person whose feet is in the water. Because the initial
starting amperage and/or voltage reading before sea salt is added will be
slightly different from person to person and from water source to water
source, the amount of sea salt we have to add to raise the amperage to the
recommended highest starting value (usually between 1.2 to 2.0 amp) is
going to be slightly different from person to person. Even though this
initial amperage reading and/or voltage is naturally different from person
to person and from one water source to another, to do an effect detox we
artificially raise amperage to highest safe level, by adding sea salt,
just so we can generate a high concentration of negative ions. Forcing the
current to be at the same high value of 1.2 to 2.0 for everyone, has an
impact on the color you observed; the colors will tend to look more the
same for everyone. In conclusion, given that color change, is heavily
influenced by the amount of sea salt added and that we are systematically
just adding the right amount of additional sea salt to force starting
amperage to increase to the same high optimal value for everyone, then we
are also, in a sense, forcing color change to be the same or very similar
for everyone in the same geographical region because we are all using the
same water supply source and eating the same foods with the same toxins in
general.
Conclusion:
To truly observe the difference in water color from person to person, you
need ignore voltage and amperage and just use the exact same amount of
water and salt for everyone! First determine and measure the amount of
salt that will constantly give you an initial amperage reading in the
required operating range for everyone without ever exceeding 2.0 operating
amperage limit; next pre-measure multiple portions of this same quantity
to have them ready to quickly conduction multiple sessions. You may also
make/mark a waterline mark on your tub to insure you are always using the
same amount of water. If you conduct your sessions in this manner, you are
going to notice that everyone will naturally have a slightly different
staring voltage and amperage, reflecting differences in the natural
salinity, acidity, and alkalinity of the user. The fact that these values
are different is why the color changes is naturally different for each
user after the same session length (30 minutes). Color change from one
user to another naturally reflect the differences in the body stasis from
one user to another.
Special Note:
Toxins in a user's body is going to be similar to the predominant
geographic toxins. Because the human body is approximately 80 percent
water, if you normally drink the same regional water supply that you use
to run the unit, you will find that the color change produced by the water
supply and the toxins from your body are very going to be very similar.
If your regional water supply has a lot of material and toxins dissolved
in it, you will find that you will not be able to distinguish any
difference in the water color with when you run the machine with your feet
and and without your feet; the reasoning is that the color produced by the
regional water supply, will completely mask the less intense color effect
caused by the toxins from you. To see a difference in the color produced with and without feet, we suggest using distilled water. Even
so, the ability to distinguish the color effects with and without feet
will still depend on the type of array metal you are using and how much
salt is added (as discussed earlier above). This is, of course, why we say
not to pay to much attention to water color!
Disclaimer: Information provided does not provide diagnosis, prognosis, or prescribe remedies for the treatment or prevention of any illness or disease. The Aqua Health Ionizer does not include any therapies or techniques regulated by any state or provincially licensed health care profession, nor is it intended for the treatment or prevention of any disease or health condition. Information contained within this website, manual, or other supplemental materials made available in conjunction with this or other products marketed by Meridian Lifeforce Inc., is solely for informational purposes and is not intended to be prescriptive. Meridian Lifeforce Inc. is not permitted and does not make claims to consumers in support of any health benefits derived from the Aqua Health Ionizer. Before using this or any other device, you are advised to consult a physician.
|
All rights reserved. Site Design Copyright © 2005-2007 Meridian Lifeforce Inc and its licensors. All pictures and text herein are properties of Meridian Lifeforce Inc. Unauthorized reproduction of images, text, or audio-video content will be reported and prosecuted to the full extent of the law. |